Glass and aluminum near me
In the name of God
The alloy we use has chemical properties similar to Metacron from Germany, and all the machines we work with are from Italy. The services we provide on it are special services. The shot peening service we provide gives a super matte velvet-like finish on the profile. This service is exactly what the Mac system uses.
Using stainless steel shot balls, we create a 360-degree profile. For example, if you have a velvet profile and you apply this service, it covers the entire profile. Then you apply a service like natural on only the strip part. This is considered very elegant aluminum work.
Can you specify the sheet to be brushed this way, or only the profile? Only the profile, unless it can be done in the brushing section.
Can aluminum sheets also undergo this service? Yes.
Exactly with this finish or better? No better than this.
Does thickness matter to you? Usually, it’s 0.6 and above.
We usually work with 2 and above.
We bend some sheets like a box, for example, 20 cm by 20 cm, forming an angle. Can it undergo this finish? No, pieces with sheets cannot undergo this finish.
It needs to be done beforehand; it should be finished before, and then it can be painted, but not for the services.
For example, this brush in your hand cannot be done below 2.5 meters of alloy; it will throw it out.
The sheet I am talking about, suppose we make a U shape with a height of 2 or 3 meters, meaning the pieces are not small.
I doubt it can do that because the machine is under pressure and uses two of these pastes to rotate.
We give a 20-year warranty in terms of color, weather conditions, humidity; if anything happens, the company covers the costs.
In our workshops, either the line gets drawn, or it gets scratched or ironed; during transportation, it usually gets scratched, but it doesn’t get damaged.
No, that’s for abrasion. If you have high resistance, it will scratch the surface, but for a surface that should create abrasion, nothing will happen to it.
Work of such quality doesn’t require analysis.
The paints we use are all IBA paints.
The factories we work with, even for composites, say this flash is from last year.
Alborz Aluminum Company doesn’t say it’s from last year; if you call a few years later, it’s the same, no difference.
That is, the profile we get and set aside is the same.
It takes a maximum of one week to deliver our product to you.
If we take these pieces 4 cm there, can they be analyzed?
Everything is possible; it’s a cost issue. If we want to analyze the pieces, your cost increases; we do it, it doesn’t matter to us, but it goes into our parts table.
My point is, do the pieces we deliver to you work in both electrostatic and analysis? Yes.
We have 400, 500 gray colors and 600 black colors analyzed.
The color chart that includes electrostatic colors can be kept with us so that wherever we go, if we decide to work with your color, we can coordinate the codes with you.
With all our friends we work with, the color codes are global color codes.
With any paint manufacturer you work with? It doesn’t matter; our main paint standards are Kule and Cuba.
A customer comes and says my color code is PEKA; I have the color code and work with your device on a wage basis.
Is it possible to give you a paint with another brand and ask for the same color? Yes, we can do it on a wage basis.
In terms of quality, especially Pulvert, it has extremely high quality.
In general, the quality of the analysis is better than powder.
Powder paints seem thicker than analysis.
When you send a profile, even if the profile is weaker, it goes for finish work, and there, the profile comes out with maximum quality, and then it goes for analysis.
What is the price difference between analysis and your texture? It varies; this starts from 30,000, that from 45,000 per kilo.
So, there’s roughly a 15,000 difference.
The cheapest one is the one with no services, only painting.
If you want zero 6 brushes analyzed, it’s 47,000 per kilo, but with services, it becomes 58,000, and if you want shot, it becomes 107,000 per kilo.
Silver is the cheapest at 90,000, meaning both analyzed and with services and shot.
Black is 107,000.
Does the same price difference exist in stretchers? Yes, per piece, for example, a 6-meter stick.
The profiles we give have a minimum width of 1 meter and a length of 3 meters.
For example, if it’s less than 3 meters, what services do you want done? We don’t want many services, just the simplest analysis.
So, each piece is 760,000.
Without calculating the powder paint, each piece is 420,000.
Approximately 130 pieces come, which are L-shaped, one side is 1 meter, the other side is 2 meters.
The rest comes as sticks, possibly 4-meter sticks, 6-meter sticks, then there are some angles, some boxes which are 5.5 or 6 meters. Glass and aluminum near me Glass and aluminum near me Glass and aluminum near me
Leave A Comment